Making a bathroom out of plastic
When making repairs in the bathroom, due attention should be paid to the material that you will use, because the bathroom is the wettest place in the house. And plastic panels are a very good option in this case, because they are convenient for installation, they are easy to wash, there is a very large selection of different color variations and the price is quite reasonable.
To get started, you need to:
· wooden block or slats;
· self-tapping screws;
· dowels;
· Meter and level;
· jigsaw;
· rotary hammer or drill;
· plastic panels, the number of which is calculated according to the size of your room;
· sealant or silicone;
· antifungal medication.
Should the room temperature in which you will work be below 10?C. The plastic panels that you will be working with should be brought indoors at least an hour before work so that they become at room temperature and do not deform when they are fixed.
Pay due attention to the layout of the panels, plan where the pipes, switches, and sockets are located. Additional bars need to be made in the places where sockets, switches, and hooks will be located.
Before starting work, the walls must be thoroughly cleaned of old tiles and plaster. Next, you should treat all the walls and ceiling with an antifungal agent.
If you have a small bathroom, then you should choose light–colored panels - this will help visually increase the space of the room.
Start working from the ceiling. To do this, you need to build a frame on the ceiling from wooden bars or slats, which are attached with screws. At the same time, the bars must be sufficiently dried and of high quality. Plastic panels are attached to each other.
When the ceiling is ready, proceed to the walls. You need to start from the most noticeable angle, so that the direction of the joints is not visible later. First you need to build a frame on the walls using beams or slats. Cut the required length of the beams along the width of the wall using a jigsaw. The bars should be fixed horizontally to the wall at a distance of close to 40 cm. This will help to avoid cracks in the panel and its bending. The bars are attached to self-tapping screws, for which holes are prepared in advance and dowels are hammered. You need to fasten the panels very tightly until you hear a click.
At the end of the work, it is necessary to treat the seams of the plastic panels with sealant or silicone – this will help to avoid water penetration between the panels. Plastic skirting boards can be attached at the junction of the floor and wall, which will serve as additional fasteners for the panels. Best porn site https://noodlemagazine.com - Watch porn.
When making repairs in the bathroom, due attention should be paid to the material that you will use, because the bathroom is the wettest place in the house. And plastic panels are a very good option in this case, because they are convenient for installation, they are easy to wash, there is a very large selection of different color variations and the price is quite reasonable.
To get started, you need to:
· wooden block or slats;
· self-tapping screws;
· dowels;
· Meter and level;
· jigsaw;
· rotary hammer or drill;
· plastic panels, the number of which is calculated according to the size of your room;
· sealant or silicone;
· antifungal medication.
Should the room temperature in which you will work be below 10?C. The plastic panels that you will be working with should be brought indoors at least an hour before work so that they become at room temperature and do not deform when they are fixed.
Pay due attention to the layout of the panels, plan where the pipes, switches, and sockets are located. Additional bars need to be made in the places where sockets, switches, and hooks will be located.
Before starting work, the walls must be thoroughly cleaned of old tiles and plaster. Next, you should treat all the walls and ceiling with an antifungal agent.
If you have a small bathroom, then you should choose light–colored panels - this will help visually increase the space of the room.
Start working from the ceiling. To do this, you need to build a frame on the ceiling from wooden bars or slats, which are attached with screws. At the same time, the bars must be sufficiently dried and of high quality. Plastic panels are attached to each other.
When the ceiling is ready, proceed to the walls. You need to start from the most noticeable angle, so that the direction of the joints is not visible later. First you need to build a frame on the walls using beams or slats. Cut the required length of the beams along the width of the wall using a jigsaw. The bars should be fixed horizontally to the wall at a distance of close to 40 cm. This will help to avoid cracks in the panel and its bending. The bars are attached to self-tapping screws, for which holes are prepared in advance and dowels are hammered. You need to fasten the panels very tightly until you hear a click.
At the end of the work, it is necessary to treat the seams of the plastic panels with sealant or silicone – this will help to avoid water penetration between the panels. Plastic skirting boards can be attached at the junction of the floor and wall, which will serve as additional fasteners for the panels. Best porn site https://noodlemagazine.com - Watch porn.